Pinned

Community Guidelines

How to post in the Miniature Armor Library: relevance, accuracy, respect, one topic per submission, no promotion — and how moderation works.

By Hong Kong Miniature Armor Co. Ltd. · Last updated October 2026

A 1:6 knight bust sits on the packing bench next to a steel rule, and the rule is the part a first-time contributor forgets to include in a photo. Without it, a 114 mm helmet and a 135 mm one look identical on a screen, and a thread that should be about construction becomes a guessing game about size. The note below is how we keep the Library honest about scale before a single comment is posted.

By the end you will be able to check any submission against two numbers we hold to: a 1:6 figure is 17 cm tall and its 1:12 cousin is 8.5 cm, and a post that shows neither is asking the reader to trust the eye alone. We would rather you could measure.

Stay on subject

Everything here is about historical arms, armor, helmets, blades, their construction, their history and the collecting of them. Fantasy, anime and modern tactical discussions belong elsewhere.

Be accurate, and be honest about uncertainty

If you are quoting a museum record, a catalogue or a book, say so. If you are not sure, say that too — "I think this is a 15th century sallet, but the visor looks later" is a better contribution than a confident guess.

One topic per submission

Comparisons are welcome ("Jian or Dao — how can I identify it?"). Shopping lists, price requests for unrelated goods and general chat are not.

Be respectful

Corrections are welcome and encouraged. Rudeness, gatekeeping and personal attacks are not. Assume the other person knows something you do not.

No promotion

No unrelated advertising, affiliate links or spam. Linking a museum page, a catalogue entry or a well-sourced article to support a point is fine and encouraged.

What happens to your submission

Community topics are reviewed before publication. We do not edit your words, but we may decline a topic that breaks the rules above. Replies use Shopify's native comment system, so anything you post can be removed if it breaks these guidelines.

The 1:6 and 1:12 line, drawn at 17 and 8.5 cm

Our own scale line runs on two heights. A 1:6 figure is 17 cm from base to crown; halve that and you get the 1:12 figure at 8.5 cm, because 17 ÷ 2 = 8.5. That ratio is the first thing a contributor should state, and it is the one most posts omit. When a reader cannot tell whether a helmet is 114 mm or 135 mm, every claim about its weight and detail is built on a guess, and the thread drifts into taste instead of evidence.

The failure mode we see most is the scaleless photo. A piece photographed on a palm or a keyboard looks monumental and tells no one its true size, so the next contributor scales their own guess to it and the error compounds down the thread. The fix is dull and absolute: we ask for a millimetre rule lying beside the object, or at minimum the base diameter in the caption. A 1:6 bust base is a known circle; print the number and the photo becomes a measurement instead of a mood.

The judgement call follows from the rule above. We do not host fantasy, anime or modern tactical kit, because a historical Library that admits a fictional prop loses the one thing that makes a scale claim mean anything: a real object to measure against. A replica that quietly implies a scale it does not state is the same fault in miniature: it asks to be trusted, not checked. Say the height, show the rule, and the comment earns its place.

The ruler is not the only honest reference. A coin or a figure of known height in the frame does the same job, and we accept either, because the point is a fixed object the eye can measure against, not the brand of the rule. The posts we publish are the ones that state the scale in the first line and then show it; the ones we send back open with a confident identification and only reveal the size when pressed. A contributor who leads with the number has already done the work.

The bust range sharpens the same lesson. Our fixed-height busts run from 114 mm to 218 mm, sold by height rather than by ratio, and a 218 mm piece is not '1:6' just because it looks large — a 1:6 full figure is 17 cm and a 1:12 is 8.5 cm, while a 114 mm bust is neither. Height alone does not fix the scale, so an honest post names the number on the base and lets the reader place it. Vague 'roughly half scale' wording is the gap a ruler closes, and the Library is built for the measurement, not the mood. The same discipline applies to every link and product page in the thread: a scale stated once, at the top, spares every reader the guesswork, and it is the habit that keeps the Library's comments useful rather than ornamental. A number in the first line is the whole rule, and the ruler is what makes it true.

Sources & References

  1. Royal Armouries — Treatise on Armour and collection object records.
  2. The Metropolitan Museum of Art — Arms and Armor collection documentation.

FAQ

Can I post a fantasy or anime piece to the Library?

No. The guidelines restrict the Library to historical arms and armour and the collecting of them; fantasy, anime and modern tactical gear belong elsewhere. A post that stays on subject and names its scale is the one we can publish and others can check.

How do I show the true size of my piece in a photo?

Lay a millimetre rule beside the object, or give the base diameter in the caption. A 1:6 bust base is a fixed circle, so printing its width turns a photo into a measurement. Without that reference, a 114 mm and a 135 mm helmet look the same on screen.

Why does the Library care about uncertainty in a date?

Because a photo cannot prove a date, only suggest one. Phrase a post as 'consistent with' rather than 'is', name the clues that support it, and invite correction. The strong threads are the ones where three readers converged on a range, not the ones that opened with a confident year.

MA
Hong Kong Miniature Armor Co. Ltd.
The research and bench team behind miniaturearmor.com. We build 1/6 and 1/12 armour and weapons in our own workshop in Zhuhai — assembly, CNC and 3D printing under one roof — and every piece passes through our hands before it is packed. These notes come from the bench: fit, finish, rust, and the compromises scale forces on a design.

Join the Discussion

Have a question, correction, historical reference or collector insight? Join the discussion below.

Please keep discussions respectful, relevant and historically focused. Spam, unrelated promotions and unsafe content may be removed.Community guidelines.

No replies yet

Be the first to add a question, a correction or a collector insight about this topic.

Post a Reply

Replies use Shopify's native article comments — nothing is stored outside your store.

Your email is never published.

Your comment will appear after review.