Step by step through a medieval shield: edge-joined boards, linen and casein glue, gesso and paint, the boss, enarmes, and the rawhide rim that out...
EuropeanArmor
Gorget and Plackart: The Joints That Let a Harness Move
A full harness is three joints, not one box. How the gorget frees the neck and the plackart stiffens the waist, why the overlap and the gap matter, and how to spot a modelled articulation on a 135mm bust.

Contents
By Hong Kong Miniature Armor Co. Ltd. · Last updated October 2026
Put on a full harness and the first thing you notice is not the weight. It is that you cannot look down. The breastplate stops your chin at about twenty degrees. Bend sideways and the plates on your flank dig in. Raise an arm and something sharp finds the top of your shoulder.
None of that is a design failure. It is the price of the two pieces that make a harness wearable at all: the gorget at the throat and the plackart over the belly. Between them they turn a rigid steel box into something a person can turn, breathe and ride in — and they are the parts most often modelled badly on a miniature, because their whole job is to be almost invisible.

Three joints, three different problems
A cuirass covers a torso that moves in three ways, and each movement needs its own solution.
The neck rotates and tilts. A helmet sits on a head that turns perhaps 80 degrees to either side and tilts forward to look at the ground. If the breastplate came up to the jaw, the head would be locked. The gorget exists to bridge that gap: a collar of two or more plates that covers the throat and the top of the chest without touching the chin.
The waist bends and twists. The lower spine flexes forward, extends back and rotates slightly. A single rigid tube from armpit to hip would fight all three. The plackart is the answer: an additional plate over the belly that overlaps the breastplate, so the two can slide a little against each other instead of fighting.
The shoulder lifts. That problem belongs to the pauldron and its turner, and it is a separate article. But it explains why the gorget’s top edge is cut low at the sides: the shoulder has to be free to rise past it.
The gorget: two plates and a gap
A fifteenth-century gorget is usually two main plates — front and back — joined at the sides by a hinge, a strap or a sliding rivet, and closed at the front by a buckle or a pin. Some are made of several lames each, which lets the collar follow the neck’s curve more closely. The upper edge is rolled or turned so it does not cut.
The critical dimension is not the plate thickness. It is the gap. A gorget sits over the top of the breastplate and under the helmet’s lower edge, and both of those neighbours move. Too tight and the collar locks the head; too loose and a point can find the gap between gorget and breastplate. Armourers solved this with overlap and leather: the gorget’s lower edge laps over the breastplate’s neck opening, and a leather strip under the steel takes the wear where the two rub.
Weight is modest — roughly half a kilogram to a kilogram on a full-size harness, depending on how many lames. That is a small fraction of a 20 to 25 kilogram field harness, and it buys the difference between a wearable helmet and a steel collar you cannot turn in.

The plackart: a second skin over the belly
The plackart appears in the last decades of the fourteenth century, and its name comes from placke — a plate. It is an extra layer over the lower breastplate, covering the belly from the bottom of the chest to the top of the fauld. Early examples are clearly a separate piece fastened on with straps or points; by the mid-fifteenth century many are riveted permanently to the breastplate with a row of flush rivets along the join.
Why add a plate where the body is softest? Two reasons. First, that is exactly where a lance or a sword point arrives in a mounted collision, and the plackart doubles the steel without thickening the whole breastplate. Second, the plackart is where a harness is stiffened against bending — a curved plate over the belly resists a forward blow far better than a single sheet that has to flex.
The visual signature is the horizontal seam across the waist, with the plackart lapping over the breastplate. On a harness with a media waist — the pointed, V-shaped waist of the 1450s onward — the plackart is shaped to follow it, which is one of the details that dates a piece.
Bench note: modelling a joint at 1:6
At 1:6 the gorget is about 18 mm tall and the plackart seam sits roughly 45 mm below the collar. Both details disappear if the piece is cast as one shell — so we cast the collar separately and fit it over the breastplate’s neck opening, with a dark gap of about 0.4 mm between them. That gap is not a defect. It is the articulation, and it is what makes the silhouette read as armour rather than as a statue.
We do not paint the seam shut. A line of paint across an articulation is the fastest way to make a miniature look like a toy: the eye reads a continuous surface, and the joint stops existing.

From protection to insignia

By the seventeenth century the gorget had outlived the armour it belonged to. Field harnesses shrank, then vanished from most infantry; the gorget stayed, worn over a buff coat or a uniform as a badge of officer rank. These command gorgets are small: a front and back plate, often gilt or engraved, hanging from a ribbon or a strap, with no pretence of stopping a blade.
That afterlife is useful for dating. A gorget with elaborate engraving and no matching breastplate is not a fragment — it is a complete object of its period, made to be seen rather than hit. Museums hold far more of these than most people expect, and the labels usually say “officer’s gorget, 17th century.”
What to check on a 135mm bust
Four details tell you whether the maker understood the joint or just copied a photograph.
The collar should overlap the breastplate, not sit on top of it like a ring. Look for a step at the lower edge.
The plackart seam should be a real step. A decal line is flat; a modelled seam has a shadow at its lower edge.
The neck opening should be wider than the cast neck. If the gorget touches the neck all the way round, the piece would not articulate.
The top edge should be turned. Even at this scale, a rolled edge reads as a rolled edge and a square cut reads as a cut.
To compare seams on real harnesses, the Wallace Collection has a run of fifteenth-century armours where the gorget’s lower edge and the plackart join can be read at eye level, without a case between you and the steel.

The Met’s conservators dress a mannequin in a full harness — the best available look at how the neck, chest and waist plates actually overlap.
Questions about gorgets and plackarts
Was a gorget worn with mail underneath?
Often yes, especially earlier. A mail standard or collar fills the gap between helmet and gorget, which is precisely where a point can enter. By the late fifteenth century the arming doublet’s high collar does part of that job.
Why is the plackart thicker than the breastplate on some harnesses?
Because it can be. The belly plate is smaller and flatter, so adding thickness costs less weight than thickening the whole breastplate. Thickness in armour is always a compromise with how far the piece has to be carried.
Is a missing gorget a big deal on a collector piece?
On a full harness, yes — it changes the silhouette and the dating. On a bust, the gorget is usually integral to the composition, so its absence is a modelling choice rather than damage. Judge the object you are looking at, not the harness it might once have belonged to.
Keep reading in the Miniature Armor Library
- Jian: The Chinese Straight Sword, Explained
- Knight Helmet Types: Great Helm, Bascinet and Armet
- Dao Sword: The Chinese Saber, Explained
- Sword Types: A Field Guide to Blades and Hilts
- Katana Stand and Wall Mount: How to Display a Sword
Choosing your first piece: start with the Roman Helmets, Japanese Weapons, Chinese Armor & Weapons or European Armor collections. For long-term care, our care & maintenance guide covers cleaning and storage; and if a question needs a human, write to us — the team that answers is the team that packs your order.
The gorget and the plackart are the least decorative plates on a harness and the ones that make it wearable. If you want to know whether a miniature was designed by someone who has thought about a body inside it, start at the neck opening and the waist seam. Everything else is surface.
Pieces in this guide
- Medieval Knight Gorget & Plackart - 135mm Armor Bust — $45 · Gorget and plackart, modelled as separate plates
- 190mm Medieval European Knight Full Plate Armor Bust Figurine — $99 · Full plate bust, one-piece shell to compare
- 190mm Medieval European Knight Full Plate Armor Bust Figurine — $139 · Alternate finish, same articulation
- 1/6 Scale Medieval European Knight Armor Figurine with Sword — $159 · 1:6 figure in full harness, sword in hand
- Complete General Armor & Weapon Set - Collector Display — $88 · Full set with harness and weapons
- Medieval Knight Great Helm - Engraved Faceplate - 135mm Bust — $45 · Great helm — the head that needs a gorget below it
- Medieval Bascinet Helmet - Pointed Snout Visor - 135mm Bust — $45 · Bascinet with snout visor, neck coverage
- Medieval Bascinet Helmet - Pivoted Visor with Perforations - 135mm — $45 · Bascinet with pivoted visor
- 165mm Medieval Knight Helmet Model Bust Replica — $119 · Knight helmet bust, collar line visible
- 130mm Medieval European Knight Helmet Model Bust Replica — $69 · Knight helmet, alternate size
- Medieval European Knight Armor Picture Frame Decor — $129 · Framed knight armour, front view
- Medieval European Knight Armor Picture Frame Decor — $189 · Framed knight armour, larger format
The research and bench team behind miniaturearmor.com. We build 1/6 and 1/12 armour and weapons in our own workshop in Zhuhai — assembly, CNC and 3D printing under one roof — and every piece passes through our hands before it is packed. These notes come from the bench: fit, finish, rust, and the compromises scale forces on a design.
Join the Discussion
Have a question, correction, historical reference or collector insight? Join the discussion below.
Please keep discussions respectful, relevant and historically focused. Spam, unrelated promotions and unsafe content may be removed.Community guidelines.
No replies yet
Be the first to add a question, a correction or a collector insight about this topic.